Dongguan Jinyu Automation Equipment Co., Ltd.

jinyu.auto@aliyun.com

86-0769-85624738

HomeNews

News

  • How to Clean the Dispenser Parts?

    20

    12-2021

    How to Clean the Dispenser Parts?

    From a social point of view, use recyclable environmentally friendly solvents for cleaning. This method is the most popular, environmentally friendly, recyclable, and has a good cleaning effect. However, as a company, due to the high cost and the need for independent systems and equipment to be used, it is often difficult for companies to accept. Therefore, we have counted the specific cleaning methods of dispenser parts as follows: 1. Dispensing needle: The bending or abrasion of the needle and stopper may have an important impact on the quality of the dispensing. If the temperature is high or it is not cleaned for a long time, the patch glue may also be cured or semi-cured on the inner surface of the needle and cause blockage. Check the dispensing needle regularly and clean up if contamination is found. Immersion of the needle in a compatible solvent is a common method, but it is too inefficient to remove all uncured material by immersion alone. You can use a compatible solvent high-pressure spray to blow the glue out of the inner hole of the needle, and then use dry compressed air to blow out the inner hole to dry the needle. 2. Metal template: In order to prevent the detergent from eroding the adhesive of the template and the screen, use the pre-washing process, use a stronger detergent, and manually operate to avoid the contact between the detergent and the adhesive, and then use the ordinary detergent to clean the template. 3. Plastic template: When cleaning the plastic template, electrostatic discharge may occur. Therefore, special anti-static cleaners should be used to avoid this phenomenon. At the same time, do not manually clean with a rag, because the plastic is easily scratched, which may cause printing quality problems for a long time. The cleaning of the dispenser is an important part of the daily maintenance of the dispenser. 4. When the fully-automatic glue dispenser discharges g

  • 09

    12-2021

    How to Maintain the Hot Press?

    1. The hydraulic oil should be kept clean, and the oil pool should be covered and sealed. The filter screen of the oil pump suction pipe should be kept intact, and if it is damaged, it should be replaced in time. During maintenance, the sediment in the pool should be removed, the oil should be clarified or filtered before use, and all the emulsion should be replaced. This is also very important for protecting oil pumps and precision valves. 2. Partial wear of the piston is also one of the causes of surface scratches and seal ring wear or squeezing. It is caused by the fact that the thickness of the wet slab is often inconsistent with the left and right sides, and the uneven load is generated when the press is pressurized. The matching accuracy of the piston and the cylinder liner is D (dc4), and too large a gap can also cause eccentric wear. 3. For the oil cylinder that frequently leaks, the piston should be lifted out to check the surface condition, especially the part of the sealing position at the highest pressure, and should be replaced when the damage is serious. If there is eccentric wear, check the matching accuracy of the piston and the cylinder liner, and take measures to prevent eccentric wear in the production process. 4. The upper and lower liners of the hot press plate protect the surface of the hot press plate. The upper liner directly affects the surface quality of the slab, and wood bundles and other dirt are often trapped between the liner and the hot press. The liner should be removed regularly to remove the dirt. The upper liner is generally changed once a week to polish the surface and ensure the quality of the finished board.

  • 03

    12-2021

    How to Deal with Glue Hanging on the Dispenser?

    Common problems when using high-viscosity glue for automatic and desktop dispensers are nozzle/needle sticking glue, residual glue, sticking glue, residual glue will produce wire drawing or large ends/tails, which will affect the quality of the dispensing effect. Let's look at the solution below: Cleaning position for discharging and wiping: Install a vacuum discharging device on the machine to clean the needle or nozzle at the cleaning position after each dispensing is completed. In addition, if it is a relatively awkward needle or nozzle, you can directly use nylon Wipe with a cloth to remove any glue or residual glue. Suction back: Use a controller with suction back function. The air pressure of the controller is connected to the feeding tube. When the dispensing is finished, the feeding air pressure is switched to the suction air pressure to suck the glue back into the nozzle. Pay attention to adjust the amount of suck back Re-suction is sufficient to ensure that the nozzle is free of glue. Excessive suction will affect the next glue output. Heating glue: The viscosity of the glue will decrease with the increase of temperature, and the viscosity will increase with the decrease of temperature, so heating enhances the fluidity of the glue to avoid hanging glue. Closing the valve in advance: closing the valve body in advance, in the programmed trajectory gluing, turn off the valve body switch before reaching the end point, and run the remaining part of the programming distance with the remaining pressure and remaining glue and other parameters unchanged, that is, Can avoid hanging glue or residual glue and wire drawing at the end.If you are using a spray valve, you can set the valve to close in advance in the parameters, that is, turn off the glue switch in advance. At this time, there will be glue hanging on the needle and the programming stroke has not ended, and the atomization is still Continue t

  • 22

    11-2021

    What Should I Do if the Silicone Product Smells Too Strong?

    Silicone products can be seen everywhere in our lives. Sometimes the silicone products we buy will have some pungent odors. How can we remove these odors? 1. Ventilation method The method we often use for odorous silicone products is to put them in a ventilated place, and let the odors dissipate through air flow. The new basketball shoes will have the smell of silicone, because they are all made of silicone outsole, so the new shoes we buy will be placed in a ventilated place. 2. Boiled method Boil the purchased silicone products in water to remove the peculiar smell, but these products must be high temperature resistant silicone products. 3. Grapefruit peel deodorant/activated charcoal deodorant Some special products cannot be boiled. You can use bags or boxes to put grapefruit peel or activated carbon and silica gel products together. Both grapefruit peel and activated carbon have a strong deodorizing effect. This method can also be used if the silica gel in the car is very thick. Put some activated carbon or grapefruit peel in the car. The three methods listed are the easiest way to deodorize. In fact, the main reason for these problems is that in order to save costs, some silica gel factories use ordinary vulcanizing agents that are not environmentally friendly and inexpensive, instead of environmentally friendly odorless vulcanizing agents that can completely pass ROHS testing. The vulcanizing agent is a kind of catalyst that promotes the vulcanization and molding of silica gel raw materials. It will volatilize after molding the silica gel product, and only a small part will remain, which will be volatilized after 48 hours. The vulcanizing agent will not harm human products, but the low-cost vulcanizing agent will produce a burnt and pungent smell, which will evaporate for about a month. Therefore, when choosing silicone products, try to choose better performance and odorless silicon

  • 15

    11-2021

    Why Does the Piston Rod of the Electro-hydraulic Push Rod Move Slowly or Not?

    1. Check if there is enough hydraulic oil in the oil tank of the electro-hydraulic push rod Cause analysis: The oil level in the oil cavity is low, and the oil pump sucks in air during the oil suction process. Because air is highly compressible, the system pressure will drop after inhaling air, and the system pressure drop will directly lead to unstable or slow movement of the piston rod. Solution: Fill up the oil or make the electro-hydraulic push rod work at full stroke to exhaust air. 2. Check whether the overflow valve bolt is loose and whether the iron wire passing through it falls off Cause analysis: the overflow bolt is loosened due to vibration, and the pressure adjustment of the overflow valve is too low: the pressure adjustment of the overflow valve is too low, resulting in the system load being too low. Solution: Adjust the system pressure. 3. After eliminating the above reasons, finally confirm the internal leakage of the hydraulic cylinder Cause analysis: If the hydraulic cavity leaks, the viscosity of the hydraulic oil becomes low, which will cause internal leakage in the hydraulic cylinder; wear or loose fitting of the piston rod sealing ring will also cause the hydraulic cavity to leak; internal leakage will cause the piston rod to move slowly; Solution: Replace the hydraulic oil of the electro-hydraulic push rod or replace the sealing ring.

  • 12

    11-2021

    How to clean the silicone phone case when it is dirty?

    Except for sleeping, most mobile parties will pick up their phones and paddle as soon as they have time. Therefore, no matter how clean the phone case is, especially the silicone phone case, it is easy to get dirty. So, how to clean the colored silicone phone case when it is dirty? What are some tips for cleaning the phone case? Clean water: If the phone case is not too dirty, you can wash it with clean water and then dry it with a soft cloth. Eraser: Use an eraser to wipe off the stolen goods. If the dirt on your phone case is not too serious, use the eraser several times to clean it up. Toothpaste: Toothpaste is used to clean the case of the mobile phone and repeatedly wipe with a mirror cloth to achieve the cleaning effect. Toothpaste is also a good cleaning tool. Soap: If there is a small stain on the silicone phone case, you can dip your finger in water and soap and wipe it lightly, and then use a dry towel to dry it. Detergent: The silicone mobile phone case can be gently rubbed with detergent, and then rinsed with water. Alcohol: It can be wiped gently with alcohol, the effect is very good. Then wipe it with a soft cloth or blow dry in a cool place. When cleaning the silicone mobile phone case, you can try to use clean water cleaning tools such as detergent, toothpaste, toothbrush, wind oil, cotton swab, eraser, and rag. It is recommended that you do not use excessive force when wiping, so as not to damage the phone case, and wait for it to dry. It can be re-inserted into the mobile phone to use.

  • 08

    11-2021

    How to improve the dispensing quality of automatic dispensers?

    How to keep the dispensing effect of the automatic dispenser in a good state is a problem that every equipment manufacturer should pay attention to. 1. The difference between glue and the choice of the corresponding glue outlet is also very knowledgeable. Ultraviolet curing glue: use black opaque syringe to avoid feeling light; Ultraviolet glue: use amber syringe, white piston and oblique needle (can block ultraviolet rays); if other needles are used, ultraviolet shielding needles can be customized; Anaerobic glue: use 10cc syringe and white polyethylene universal piston; Quick sol: Use safety piston and Teflon lined metal needle for water-based quick sol, and tapered needle for concentrated quick sol; Sealant and paste liquid: When the white piston rebounds severely, please use safe movable and oblique needles; The point-to-surface method should be used to adjust various parameters. Any changes in parameters will affect other aspects, defects may appear in multiple ways, and possible factors should be checked one by one. 2. The size and stability of the dispensing pres

  • 05

    11-2021

    Automatic Dispensing Machine Needle Selection

    1. Select the appropriate dispensing needle for the process, depending on the type of adhesive When choosing needles for dispensing, special attention should be paid to the adhesive used for dispensing. Since the type of adhesive is different, the needles used are naturally different. Many of the adhesives used in the dispensing process are basically the same. Dedicated needle. If it is a photocurable replacement dispensing process, generally speaking, a black opaque vacuum configuration is used and a needle with a white piston can block UV light. For UV glue, amber needles with white pistons are typically used in the dispensing process. When using other types of needles, the needles must be opaque to UV light. 2. Select the appropriate adhesive replacement treatment needle according to the treatment needs Actual needs must be considered when choosing a needle for the dispensing process. For instant glue instead of glue, the process of choosing a needle is different. Water-based instant glue should use a safe piston. At the same time, you should also choose a needle with a metal lining. For thick instant glue, you need to choose a tapered needle. Here's how to select a needle for the dispense process. This choice is very important for the entire dispensing process, as the use of irrational needles tends to result in no glue or discontinuity in dispensing. Mix randomly so that the needles do not interfere with the overall operation. The dispenser needle of the dispenser should be selected according

  • 30

    10-2021

    What Is The Main Difference between The Glue Filling Machine and The Glue Dispenser?

    Strictly speaking, the glue filling machine also belongs to the glue dispensing machine, because its function is very similar to that of the glue dispensing machine, and they all deal with glue. But specifically speaking, there are still some differences between the glue filling machine and the glue dispenser. For example, a two-liquid glue filling machine needs to use two glues AB. Glue A is the main glue, and glue B is a catalyst that can enhance the effect of glue. Kind of glue. We are committed to continuous improvement and research and development of the glue filling machine. If you have any needs in this regard, you are welcome to inquire. It doesn`t matter if you don`t think about it, just make a call and don`t know if some requirements are reasonable. Many times, just one phone call will solve all your troubles. If you don`t believe it, try it. Dongguan Jinyu Automation Equipment Co., Ltd. has been engaged in the dispensing machine industry for 21 years.Our service includes: Dispensing Machines,PVC Machines,Silicone Machines,Kpu Shoes Machines,Silicone Label Embossing Machines and CNC Machines.We are a professional dispensing machine maker and dispensing machine provider in Dispensing Machine industry.

  • 20

    10-2021

    Use Automatic Dispensing Machine Need to Pay Attention to Three Points?

    With the rapid development of electronic industry technology and the multi-functional requirements of enterprises for electronic product automation, the previously used perforated components can not meet the demand. The dispensing machine developed by desktop automatic dispensing machine equipment manufacturers has solved this problem for many enterprises. Many people don't know how to use the automatic dispensing machine correctly and what to pay attention to when using it. What should we pay attention to when using the automatic dispensing machine. 1. Needle size of dispensing machine In practice, the inner diameter of the needle of the full-automatic dispensing machine should be a certain proportion of the diameter of the dispensing point. In the dispensing process, the dispensing needle shall be selected according to the pad size. If there is little difference in pad size, the same type of needle can be selected, but for pads with great difference, different types of needles need to be selected, which can not only ensure the glue spot quality of the automatic dispensing machine, but also improve the production efficiency. 2. Glue temperature Generally, the epoxy resin glue used in the full-automatic dispensing machine should be kept in the refrigerator. When using, it should be taken out for standby for a period of time in advance, so as to make the glue fully consi

  • 15

    10-2021

    What are the main features of silicone injection molding machine?

    Silica gel injection molding machine has been widely used in the development of plastic industry. Silica gel injection molding machine adopts free suspension injection device to realize automatic correction of plunger and barrel and reduce wear. Silicone injection molding machine has the following characteristics: Excellent insulation performance, suitable for high-quality or high-tech electronic plugs. LSR materials are suitable for high or low temperature environments. Above 200 ℃ or below - 40 ℃, the insulation, mechanical properties and physical properties of the material remain unchanged. anti gasification and anti aging, suitable for outdoor use. It can be sterilized and is suitable for medical supplies and infant supplies. It is oil resistant and can be used in oil exploitation industry. The ejector pin can be used according to different combinations of sliding plates, and the stroke can be adjusted freely. Demoulding force, advance and retreat speed of thimble and demoulding times can also be preset as required.

  • 09

    10-2021

    Use of Automatic Dispensing Machine Need to Pay Attention to the Main Points

    1, do not rely on their own imagination, or experience to install the equipment, according to the professional instructions for equipment installation. Equipment inspection should be carried out regularly, do not wait to check, do not remember to check, it is best to adjust the installation level and accuracy every six months, make detailed records, archived for future reference; 2, do not let the equipment run with disease, should be in accordance with the specified parts and the scope of the content, do a good job of daily maintenance work, found abnormal, should immediately stop automatic, automatic dispensing machine in the use of the need to pay attention to the local notice maintenance personnel. 3, do not put the equipment in a bad environment for operation, because the production equipment has special requirements for the environment (constant temperature, humidity, shock, dust, etc.) of the equipment, should take appropriate measures to ensure that the performance and accuracy of the equipment is not affected; 4, do not use or substitute lubricating oil, wipe materials and cleaning agent. 5, do not make the production equipment rough processing use, do not overload performance use. To operate in strict accordance with the processing specifications stipulated in the dispensing machine equipment instructions; 6, do not remove the dispensing machine, in daily maintenance is generally not allowed to remove, e

  • 27

    09-2021

    What are The Methods of Controlling The Quantity of Glue Dispenser?

    One is the glue temperature. High speed dispenser can control the viscosity of glue by controlling the temperature of glue. Generally speaking, the greater the viscosity of glue, the greater the flow resistance, the less the amount of glue. It can be seen that the viscosity of glue has a great influence on the performance of dispensing. Because the glue material of the glue dispenser and spray paint machine can not be modified after selection, the glue dispenser manufacturer is generally controlled by the temperature of the glue. The second is fluid pressure. Dispensing machine manufacturers mainly through the control of fluid pressure to control the dispensing speed of high-speed dispensing machine. Generally speaking, the greater the fluid pressure, the more glue through the valve port, the more glue, the faster the glue. However, due to the limitation of the valve port itself, the amount of glue will not change with the fluid. The pressure builds up and builds up indefinitely. The third is injection pressure. Injection pressure is the key to control the dispensing machine to spray glue line. The higher the injection pressure, the thinner the glue line. The higher the spray pr

  • 11

    09-2021

    PVC Picture Frame Moulding Production Line Baking Oven for Colored PVC Product PVC Equipment

    Suitable for baking baking PVC products, water circulation cooling device. Simple and convenient operation, the temperature can reach 300 degrees Celsius, the temperature can be controlled. application: Parameters Table: Detail of practical oven machine Advantage of dual-station oven machine

  • 10

    08-2021

    How to Clean the Dispenser?

    How to clean the dispenser? In the traditional cleaning process of dispensers, chemical solvents such as dichloromethane, chloroform and other volatile solvents are often used to clean the mixing head. The invention has the characteristics of thorough cleaning, low cost and the like. However, due to the volatility, toxicity, non-recyclability, and environmental pollution of chemical substances, the use of solvent cleaning is increasingly restricted. Use recyclable and environmentally friendly solvents for cleaning. The invention has the characteristics that the solvent can be recycled for multiple use, and the cleaning effect is good. However, the cost is extremely high, and a separate circulation system is required to be used in conjunction with the equipment. Both the equipment investment cost and the solvent procurement cost are very high, and it is difficult for many users to bear the high cleaning costs. High pressure water cleaning. The method is non-toxic and low-cost. It has the following advantages: Realize the whole process of environmental protection operation, no pollution, harmless to operators; Simple operation, saving solvent cost; The optimized design of the cleaning channel makes the cleaning more thorough, the equipment has a longer service life, and is more stable and safer. Reduce the pre-gluing time, reduce the loss of glue, and reduce the production cost.

  • 05

    08-2021

    Application of Automatic Dispenser in the Underfill Process

    The underfilling process is to apply epoxy glue to the edge of the flip chip. Through the "capillary effect", the glue is sucked to the opposite side of the component to complete the underfilling process, and then the glue is cured under heating. Does the underfill process have any performance requirements for the dispenser? 1. The underfill must first heat the glue and maintain the temperature of the glue. Therefore, our dispenser equipment must have a thermal management function. 2. The underfill process needs to heat the components, which can speed up the capillary flow rate of the glue and provide a favorable guarantee for normal curing. 3. The underfilling process also requires high dispensing accuracy, especially when the RF shielding cover has been assembled in place, the dispensing operation needs to be performed through the upper hole. In summary, the above is the performance requirements of the underfill process for the dispenser. We must pay special attention to the underfill process during the process of dispensing. Our service includes: Dispensing Machines,PVC Machines,Silicone Machines,Kpu Shoes Machines

  • 27

    07-2021

    What Factors Sffect the Accuracy and Quality of the Dispensing Machine?

    During the long-term use of the automatic dispensing machine, due to the friction between the parts, some precision errors may occur in the product dispensing, which will affect the dispensing quality. So, what are the factors affecting the dispensing quality? Whether the glue output of the glue dispenser is stable or not The glue output of the glue dispenser can be adjusted according to its own needs, so the glue output rate of the glue dispenser, the glue output time, the glue stop time, and the size of the glue will be affected. The degree of wear of the accessories affects the automatic dispensing machine to ensure that the automatic dispensing machine is used for a long time and maintains a stable dispensing accuracy. Will the accuracy of multiple products be affected by one dispenser? Because our dispensing route is mainly controlled by programming, and programming can be stored in large quantities, an automatic dispensing machine is not limited to ordering one product, as long as the programming is set, and then the phase difference parameters are matched to the machine. , You can dispense glue, it doesn`t matter how many products you order, but you need to make corresponding fixtures and fix the products. Can the dispensing quality of different products be consistent? Due to the product specifications, size, appearance and shape, etc., the product may be different, and the dispensing quality requirements will also be different. But as long as the machine is well maintain

  • 19

    07-2021

    Maintenance Knowledge of Dispenser

    The daily maintenance of the dispenser directly affects the service life of the dispenser. The daily maintenance of the dispenser has a great impact on the service life of the dispenser, including its smoothness in normal use. The following are the routine maintenance steps of the dispenser: 1. To replace the type of glue, clean the pipeline. At this time, first close the feed valve and open the discharge valve. After the remaining rubber material is discharged from the rubber tank, close the discharge valve and open the feed valve to pour the cleaning solvent into the rubber storage tank, activate the body, and press the solvent according to the usual operation method.rinse. 2. If the air pressure is abnormal and water vapor is found, please remove the water vapor in the pressure regulating filter or check whether the air pressure source is abnormal. Before the glue dispenser is used in large quantities, please try a small amount first to master the use skills of the product to avoid errors. When the test is no problem, then use the double-liquid glue machine or the double-liquid glue machine for mass production; pump The vacuum system vacuumizes the glue to remove bubbles during the mixing process, or let it stand for 10-20 minutes before use, so that the bubbles generated during mixing are removed in time, and the more glue is mixed together. 3. Please clean the machine part regularly to increase the service life. The more the amount of glue mixed together, the faster the reaction and the faster the curing speed. Therefore, the glue must be reasonably formulated according to the actual production situation, otherwise it will cause the waste of glue. Eliminate accidents and improve production efficiency. Nowadays, liquid control technology and dispensing equipment are widely used in various production fie

  • 16

    07-2021

    How to Solve the Problem of Glue Dripping During the Dispensing Process

    The problem of dripping during the dispensing process may be due to the poor quality of the dispensing valve, wear and corrosion of the seal, too thin glue, excessive air pressure, and too small diameter of the dispensing needle. Low-quality dispensing valve, leaks, processing accuracy is not high, the valve cannot be closed firmly, it will cause glue drop. If the valve is used for a long time, or the glue itself is corrosive, it will cause the damage of the seal. In this case, the valve will have a seal when the glue is closed, and the effect of sucking back will be greatly reduced, and the glue will also drop. So when the valve has been used for a long time, there will be glue dripping, first change the seal and try it! If the glue is very Dilute, you can change to a thicker one with the same glue, and the problem will be solved; if the air pressure is too high, it will also cause glue, try reducing the air pressure; if the dispensing needle is too large, Change to a smaller one In addition, if the reason is the leakage of the rubber valve, the following methods can be adopted: The leaking of the rubber valve often occurs after the valve is closed. 95% of this situation is caused by the diameter of the needle being used too small. A needle that is too small will affect the flow of liquid and cause back pressure, resulting in dripping shortly after the dispensing valve is closed. A needle that is too small will also affect the bubble discharge action when the valve starts to use. Just replace the larger needle to solve this problem. The tapered oblique needle produces the least back pressure and the liquid flow is the smoothest. The air in the liquid will leak after the glue

  • 24

    06-2021

    How to Extend the Service Life of the Dispensing Machine

    1. If the air pressure is abnormal and water vapor is found, please remove the water vapor in the pressure regulating filter or check whether the air pressure source is abnormal. Before the glue dispenser is used in large quantities, please try a small amount first to master the use skills of the product to avoid errors. When the test is no problem, then use the double-liquid glue machine or the double-liquid glue machine for mass production; pump The vacuum system vacuumizes the glue to remove bubbles during the mixing process, or let it stand for 10-20 minutes before use, so that the bubbles generated during mixing are removed in time, and the more glue is mixed together. 2. The machine should be unplugged when the machine is out of service for a long time. This will not only extend the life of the machine but also save a lot of electricity bills. With the needs of the ever-changing industrial development, liquid control technology and dispensing equipment are also constantly developing to ultra-high precision control and diversification and specialization. 3. To replace the rubber type, the pipeline needs to be cleaned. At this time, first close the feed valve and open the discharge valve. After the remaining rubber material is discharged from the rubber tank, close the discharge valve and open the feed valve to pour the cleaning solvent into the rubber storage tank, activate the body, and press the solvent according to the usual operation method. 4. Please clean the machine part regularly to increase the service life. The more the amount of glue mixed together, the faster the reaction and the faster the curing speed, so it is necessary to make a reasonable mix of glue according to the actual production situation, otherwise it will cause a waste of glue. Eliminate accidents and improve production efficie

  • 18

    06-2021

    How to Distinguish between Dispensing Machine and Glue Filling Machine

    With the development of various industries, glue dispensers and glue dispensers have been widely used in the fields of communication electronics, LED lighting, white goods, automotive electronics, etc., but there are still some customers who are more vague about the concept of glue dispensers and glue dispensers. 1. The amount of glue and the use of glue are different between the glue dispenser and the glue dispenser The glue filling machine generally uses a large amount of glue to fill the glue, while the dispenser uses a small amount of glue or a small amount of glue to dispense. The glue water is one-component glue and two-component glue, while the one-component glue is used There are many dispensers, and the one that uses two-component glue is generally a glue filling machine. 2. The glue supply system and use nature of the glue dispenser and the glue dispenser are different Automatic glue dispensers usually use board air pressure to control the glue, while the glue filling machine uses gear pumps, screw pumps, piston pumps and other pumps to quantify, proportion and mix the two glues before filling the product according to the glue filling conditions. . Glue dispensers are suitable for product dots, coatings, rounding, and various special-shaped tracks, etc., while glue filling machines are suitable for product sealing and glue filling, and waterproof glue filling is usually based on fixed points. 3. The glue supply system and use nature of the glue dispenser and the glue dispenser are different The automati

  • 10

    06-2021

    What are the Advantages of Automatic Dispensing Machine?

    First of all, the automatic dispenser saves manpower and does not require a large number of workers to operate. Just press a few buttons. The operation is simple. Secondly, the fully automatic dispenser has very powerful functions such as loading, unloading, transportation, and dispensing. It can be a good material savings. 1. 24-hour automation can greatly improve the production efficiency of enterprises, avoid complex manual operation, slow speed, error prone and other problems, to meet the needs of mass production. 2. Easy to operate, low technical requirements for operators.Non-professionals can also quickly master the operation method, reducing the time and money for enterprises to train employees.By changing the production technology, it can be put into production quickly, conveniently and quickly. 3. It can automatically realize the whole production process, and is responsible for feeding, clamping, cutting and other work, which improves the company's original use of manual loading and unloading caused by unstable product quality and performance. 4. It can control the glue time and amount of glue, accurate control of the amount of glue, reduce the waste of glue, save costs and ensure the consistency of dispensing and dispensing quality. 5. For the closed space dispensing, it can reduce the damage caused by toxic substances to the human body, labor intensity and the occurrence of industrial accidents.

  • 05

    06-2021

    The Purpose of the Dispensing Machine

    Automatic dispensing machine has a wide influence on the industry.In industrial production, many places need to use dispensing, such as integrated circuits, semiconductor packaging, printed circuit boards, color LCD screen, electronic components (such as relays, speakers), electronic components, automotive parts and so on.Traditional dispensing is achieved by manual operation of workers. Dispensing process in industrial production is more and more, the requirements are more and more strict.The traditional dispensing is manually operated by workers. With the rapid development of automation technology, manual dispensing has been far from meeting the needs of the industry and is gradually replaced by automatic dispensing machines.Automatic dispensing machine is widely used in industrial production, such as integrated circuits, printed circuit boards, electronic components, automotive parts, handbags, packaging boxes, etc. The application of automatic dispensing machine greatly improves the production efficiency, improves the quality of products, and can realize some manual dispensing process that can not be completed.Automatic dispensing machine in the degree of automation, can achieve three axis linkage, intelligent work.

  • 20

    05-2021

    Compared with Traditional Dispensing Method and Auto Dispensing Machine

    The glue dispenser is a device that takes an automated form to control the fluid. It can replace manual glue, paint or other liquids to accurately drip or apply to the exact position of the product. Compared with manual, the glue dispenser is more accurate in operation and has high operating efficiency. First of all, the traditional manual dispensing method not only has large errors, but also the workers are very prone to fatigue when they are fixed for a long time. The biggest advantage of the dispenser is that it replaces manual operations and realizes mechanized production and control. You can set a special program to control the dispenser to dispense in accordance with the corresponding operating procedures. The entire dispensing process is very efficient and precise. Secondly, there are many application industries for dispensers, and they have strong operational adaptability as a whole. There are certain differences in the dispensers used in different industries, and different production results can be achieved in different ways. For example, in the electronics industry, it mainly dispenses mobile phone batteries, notebook battery packaging and various optical components. In addition, dispensers are widely used in the automotive industry, industrial electrical industry, and construction engineering.

Email to this supplier

Your message must be between 20-8000 characters

Home > News

Home

Product

Whatsapp

About Us

Inquiry

We will contact you immediately

Fill in more information so that we can get in touch with you faster

Privacy statement: Your privacy is very important to Us. Our company promises not to disclose your personal information to any external company with out your explicit permission.

Send